![]()
Emulex Storport Miniport Driver Core Kit Package driver#While Emulex provides management utilities to enable you to delete virtual ports, the LPFC driver cannot detect whether devices accessed through a virtual port are in use. Deleted virtual ports may appear to be mounted, but are inaccessible. When swapping cables, allow devloss timeout to fire before replacing the cables.To determine if discovery is complete read the "state" sysfs parameter. When swapping cables replace each cable, one at a time, and allow for discovery to complete before replacing the next cable.This causes all devices accessible through one or both of these initiator ports to time out and all I/O to fail. The LPFC driver may not finish discovery when two initiator ports are swapped. Emulex Storport Miniport Driver Core Kit Package drivers#Workaround: Do not add SCSI drivers right after the LPFC module in the INITRD_MODULES list. This interruption can prevent the release of the SCSI discovery reference count and the LPFC driver cannot unload. On the SLES10 SP1 system, if another SCSI driver such as aic79xx, is loaded right after the LPFC driver through the initrd image, an interruption might occur in the SCSI mid-layer discovery process on the LUNs connected to LPFC’s Fibre Channel. Issue with the LPFC module order in the INITRD_MODULES list. This is the default boot loader for most of the Linux distributions. If the LILO boot loader is used, after the LPFC driver package is installed and upon reboot, an incorrect initial ramdisk is used. LILO is not Supported The LILO Boot Loader on i386 and x86_64 architectures is not supported for this driver stream. Workaround: These messages do not indicate a functional failure and can be ignored. Emulex Storport Miniport Driver Core Kit Package code#Deleting virtual ports or performing a PCI Hot Unplug may result in SCSI errors When you delete a virtual port via the sysfs interface or perform a PCI Hot Unplug of an Emulex HBA, the kernel may report one of the following errors: kernel: Synchronizing SCSI cache for disk kernel: FAILED or SCSI error: return code = 0x00010000. Use the following command to stop the HBAnyware application: #/usr/sbin/hbanyware/stop_hbanyware 2. ![]() Stop all applications that are accessing LPFC's HBAAPI interface (HBAnyware utilities or third party applications) before performing PCI Hot Plug of an LPFC HBA. HBAAPI) to behave unpredictably or malfunction. PCI Hot Plug may cause applications to malfunction Performing a PCI Hot Plug may cause the HBAnyware utilities or third party applications that use the Emulex libraries (i.e. There are no resolved issues in this driver version.ġ. ![]() Known Issues in Driver for Linux 8.2.8.14 Resolved Issues in Driver for Linux 8.2.8.14 Supports Power Management Suspend/Resume operations. Emulex Storport Miniport Driver Core Kit Package update#Adds interfaces via the sysfs file system to update speed and topology parameters without requiring link bounce. (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) 5. Supports SuSE Linux Enterprise Server 11. ![]() Emulex Storport Miniport Driver Core Kit Package manual#Refer to the HBAnyware Utility User Manual for more information. Supports the latest HBAnyware utility version 4.1 as part of the master kit. Supports the LP21000 and LP21002 FCoE adapters. For the latest product documentation, go to If you have any questions or require additional information, contact an authorized Emulex Corporation technical support representative.ġ. The Storport KB update must be applied before the Emulex Storport Miniport driver can be installed.ĭate: March 2009 Product: Driver for Linux Version: 8.2.8.14 This document describes the new features, resolved known issues and current known issues associated with this driver build release. On FC and FCoE adapters, for Windows Server 2003, SP2 and the KB932755 update to the Microsoft Storport driver are required. ![]() In both cases, the Storport Miniport drivers are digitally signed by Microsoft and will be recognized by Windows Sever 2003, Windows Server 2008 and Windows Server 2008 R2. When the Storport MiniPort driver is used with an FCoE CNA, the driver is considered "unclassified" by Microsoft. When the Storport Miniport driver is used with a standard Fibre Channel HBA, the driver is qualified for the "Certified for Windows" logo program. Microsoft currently does not offer an FCoE WHQL "Certified for Windows" logo program. This driver supports FCoE, iSCSI and Ethernet adapters as well as FC adapters. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |